This is for using the PESIM Maule M7 with TDS GTNXi 750/650 in use. TDS pro version (latest) in use.
At least half of the time the sim crashes after take off, level out, and attempting to to use the radio (e.g., switch frequencies). Typical setup is start cold & dark, start the engine, program the 750 (flight plan, nav frequencies). Take off, climb to altitude (4000-6000 ft), level off. At this point attempting to change frequencies (flip/flop) will cause an immediate crash of the sim. This has not changed through any update of either the M7 nor the TDS product.
Of course I do not know if this is a TDS product issue or an interaction between them. A testing procedure to check or solution would be appreciated.

NEVER MIND

After realizing every plane was the same, I rebooted the computer and everything is fine again.



Have loaded the 310 several times now even with default liveries
The left GTNXi just keeps flickering none stop.
The right one is running fine.

Same thing happening in the 414

Nothing loaded but MSFS with FSUIPC7 and trackIR
Any ideas ?

Ron

Two problems only in this aircraft:
1  Only the GNS 530 is an option.  How can I get the TDS GTNXi Pro, which I own, to work?
2  The rudder does not move, only on this aircraft.

Thanks,
Howard

So starting today, when I load the the gtnxi 750 I am getting a TAWS/GPWS failure alert. Also, in the messages within the 750 I'm getting a "Data Source/Radar Altimeter source inoperable or connection to GNT lost" message. No sure why this started as before today it was working w/o any problems. Any help or suggestions would be appreciated.
Ed Henry

Greetings,

The TDS GTNxiPro is available for the Airbus H145 and H160, is there any possibility to add it to the freeware H135 ? There is already a placeholder for the PMS version.

Regards.

Just bought the product yesterday and added it to my Black Square BE350 and Black Bird PC6T.  Well done addon and I have been enjoying it, a bit spendy, but worth it if I can get a few issue worked out.  So hopefully these forums are a good place to reach out and ask for help.

1st Issue....
In the King Air, when I manipulate and push the knobs (Upper Left and Lower right knobs), I will consistently get the following message with a loss of functionality of the knobs, where they will remain in the stuck inward position and I will not have access to the push functionality to use the page change.  Any workaround or fixes?

 
https://imgur.com/a/sTfUd4k

2nd Issue...
After using the link posted on the TDS site to add the GTNxi to the PC6T, I noticed that when I select back to the 530/430 in the blackbird ipad configuration screen, that the GTNxi remains on the virtual panel overlapping the 530 and 430.  So the switch from the "Blank panel" (GTNxi) option back to the 530/430 option isn't working.  The only way to get the other option back is to uninstall the mod to put the GTNxi on the porter.   If there was a workaround or fix for this, that would be great.

Cheers.

The JustFlight PA-38 Tomahawk has been released for MSFS and features the TDS GTNXi for both the GTN750Xi and GTN650Xi in the Virtual Cockpit!
The TDS GTNXi Pro transforms the JustFlight PA-38 Tomahawk by adding the modern GPS navigator feel to a very complex aircraft created for MSFS.

Do not miss out the TDS GTNXi Pro, which offers a fully updateable Navigation Database from Navigraph as well as worldwide Navigraph Charts!

More information and to purchase the JustFlight PA-38 Tomahawk can be found here:
https://www.justflight.com/product/pa38-...-simulator

The TDS GTNXi Pro for MSFS can be purchased from the TDS Sim Software website:
https://tdssim.com/

Bonjour,

J'apprécie grandement TDS xi Pro. Cependant est-il possible de mettre le GTN750 (normal) et le 650 en lieu et place du Garmin 530. Merci de votre réponse. Bien cordialement

Hello,

I got a very frustrating issue I can’t figure out with the tdsi. I installed it over a brand new msfs installation without mods beside the official ones. 

Since  then I noticed I can’t have horizontal navigation anymore despite the indicators saying otherwise.
Vertical navigation is working as intended.

I noticed even the g1000 got that issue now.

For context, I tested the sim and my kits before installing tdsi and all AP were behaving properly. 

Removing the tdsi doesn’t change anything…

I am a bit at lost here…

Thanks for your inputs!

Eric

How can we change the speed at which the GTN flies the Smart Glide profile? It seems that it is always 88 knots. In a lot of aircraft this leads to a stall.

I actually work at a Garmin avionics shop in real life, and I know that you would hold HOME while powering on the 750 to get in the config menus to change this. But....I don't think this is possible in MSFS..right?

So how can we change the glide speed setting?

Thank you very much in advance for your time and consideration, I love the product. Bought it after your Navigraph update. I'm sure you probably had to make some crazy deal with Garmin for the Navigraph thing to even be possible. Wish I could use the same data in the RXP GTN in Xplane.

I look forward to hearing from you, and hope you have a good day/night!

Dan