I purchased a new computer and installed the latest TDS GTN750Xi software that integrates with my REALSIMGEAR GTN750Xi hardware. It worked great on my old machine running Windows 10 Pro... now after installing the MSFS REALSIMGEAR software and the TDS GTN750Xi software into the new machine running Windows 11 Pro.... I get a BLACK SCREEN both on the PC screen, as well as the the REALSIMGEAR hardware screen. I've tried to install the latest trainer and it does not install. I don't have anything other than the standard Windows Defender running.

Good day all,

as the title says, the fresh v1.1.0.4 crashes whenever FPL of at least two waypoints is created, or perhaps any active leg, with the screen remaining frozen. The sim itself keeps running, and the TDS can be reset by unpowering it (for it to crash again, this happens 100 % of the time).

Crash here:



...and here:



This is fine (no crash):



...but doing this crashes the thing:



No issues whatsoever with the previous version. Using Navigraph, on the latest database, and on A2A Comanche.

Any ideas?


Edit:

Happens when running the 'standalone' on the desktop too, so it should not be anything sim-related:



I also tested, it is enough to have a single waypoint on the FPL and then selecting Direct To there to crash.


All the best,
-Esa

Looking for some help here.  I am Navigraph Total subscriber.  I do my flight planning at the real world Garmin site FltPlan.com.  I also carry routes over into Simbrief.  Occasionally I drag and drop route lines visually at Skyvector.  All of those show a high airway from Cleveland to Baltimore, Q178.  In MSFS for G1000 and G3000, with Navigraph data, the flight plans import successfully with Q178.  However with the TDS GTN GPS gauges J178 returns an error that locks the flight plans until edited. 

I have the TDS and Navigraph linked.  In investigating related waypoints today I found the TDS GTN is evidently looking instead for J518.  In the TDS J518 has the same waypoints.  I cannot find J518 on any current charts or at any of my flight planning sites.  If I am linked to Navigraph and getting Q178 in other gauges, what then is causing this in the TDS?

(08-01-2024, 04:14 AM)fppilot Wrote: Looking for some help here.  I am Navigraph Total subscriber.  I do my flight planning at the real world Garmin site FltPlan.com.  I also carry routes over into Simbrief.  Occasionally I drag and drop route lines visually at Skyvector.  All of those show a high airway from Cleveland to Baltimore, Q178.  In MSFS for G1000 and G3000, with Navigraph data, the flight plans import successfully with Q178.  However with the TDS GTN GPS gauges J178 returns an error that locks the flight plans until edited. 

I have the TDS and Navigraph linked.  In investigating related waypoints today I found the TDS GTN is evidently looking instead for J518.  In the TDS J518 has the same waypoints.  I cannot find J518 on any current charts or at any of my flight planning sites.  If I am linked to Navigraph and getting Q178 in other gauges, what then is causing this in the TDS?

Hi

I recently purchased the H160 helicopter, everything was working fine, using the GTNXi, I updated to the latest version (1.1.0.3) of and all i get now is a black screen for the navigation. I've reinstalled the GTNXi several times but still get the black screen. The GTNXi still works with my Piper Camanche and TBM 850. When activating the software from the desktop icon it works fine. I reinstalled the H160 but still the black screen.

Any suggestions on how to fix would be appreciated

Thanks

I am just coming back to MSFS2020 after about 2 months off. After applying all updates to MSFS, AAO, BKSQ Duke, I am unable to get the 750 to display.
When I attempt to power up the avionics, the 650 turns on and displays the initial "licensed to" screen. 
The 750 displays that same screen for about 2 seconds and then goes blank. 
Running GTNXI PC Trainer 3.6.40 with Pro Upgrade (1.1.0.3)

The 750 works just fine (both positions) in the C414W. Powers up, and I can load a flight plan. Only AC I am having a problem with is the DUKE. 

Any Ideas?

I was having autopilot issues using the GTN750, so I tried reinstalling the trainer and then the TDSGTNxi.  Now the installer doesn't see the trainer (I've opened it and used it) and won't load the simulator.  Also, before I did the trainer download, when I could still install the simulator it would only load 1.0.2.2, not the recommended 1.1.0.3.
Bill Cox

I just purchased- the GARMIN TXI Trainer - but I seem to be unable to install.... I keep getting the following error messages.
(see text & attached)

Summary: Response status code does not indicate success: 503 (Service Unavailable).

Attached Files

Thumbnail(s)
   

I'm trying to use the TDS 650 in standalone (or really any mode) but it doesn't seem to be controlling the onscreen HSI at all. I went in to the TDS 650 settings and verified that it is set to control VOR 1, NAV 1, etc. But, the HSI stays flagged and the CDI does not deflect.

Additionally, it doesn't seem like the TDS 650 plans flows to MSFS. I see a lot of posts asking about going the other way, but all I care about would be TDS650 => MSFS. Is that also not a possibility (tried in both standalone and not standalone mode)

When trying to install  version 20.30.8.0 I get the following error message every time now (see link to image). My internet is fine, My firewall is down

Attached Files

Thumbnail(s)
   

Hello,

When trying to install the various versions I get the following error message every time now (see link to image).  Yes, my internet is fine, and I'm using Windows 11.  Is there something special I need to do with Windows defender?